205L Fuchs Plantogear 100 HVI

PLANTOGEAR 100 HVI
 
Miljøtilpasset, industriell girkasseolje basert på syntetisk, mettet ester. Utmerkede egenskaper mot slitasje og korrosjon. Anbefales for smøring av gir, vinkel, planet og snekkegir, spesielt i miljøfølsomme områder.
 
PLANTOGEAR 100 HVI, 150 HVI
 
Environmentally acceptable lubricating oil and EP industrial gear oil based on synthetic saturated esters PI 4-1455, Page 1; PM 4 / 03.18
 
Description
 
PLANTOGEAR 100 HVI and 150 HVI products are environmentally acceptable industrial gear oils based on special saturated synthetic esters which guarantee high ageing resistance and excellent wear protection - very good lubricity. The products have a good solvency (good deterging dispersant properties due to the polar ester base oils). PLANTOGEAR 100 HVI and 150 HVI products have high scuffing protection.
 
Application
 
PLANTOGEAR 100 HVI and 150 HVI products can be used as universal CLP industrial gear oils. PLANTOGEAR 100 HVI and 150 HVI products can be used in spur, bevel, planetary and worm gears, especially in environmentally sensitive areas. The products can also be used in drive systems in water protection areas where ground and surface water can be polluted by oil leaks. The formulation of PLANTOGEAR 100 HVI and 150 HVI is based on fully synthetic saturated high-performance esters based on natural renewable resources. The products can be used in applications where the use of synthetic lubricants are of advantage.
 
Specifications
 
PLANTOGEAR 100 HVI and 150 HVI fulfill and surpass the requirements according to:
• DIN 51517-3: CLP
• AGMA 9005/E02: EP
• ISO 12925-1: CKC/CKD/CKE
 
Advantages
 
• Good corrosion protection
• Excellent wear protection
• Excellent viscosity temperature behaviour, high viscosity index (VI)
• Miscible with mineral oil and polyalphaolefin gear oils
• Natural dissolving properties
• Based on renewable resources
• Rapidly biodegradable (> 60% acc. to OECD 301 B)
• High resistance to ageing
• Optimally suited for high and low temperature
 
Instructions for use
 
The PLANTOGEAR 100 HVI and 150 HVI products can be used as a universal industrial gear oil in new gears as well as in used gears. New gears should be flushed and rinsed before applying PLANTOGEAR 100 HVI and 150 HVI. New gears are usually partly filled with mineral oil based corrosion protection and running in oils after manufacture. If they are not completely flushed, the running in and the corrosion protection oil remains in the gear and may contaminate the PLANTOGEAR 100 HVI and 150 HVI products. Under unfavourable conditions this can result in increased foam values and this can affect the biodegradability of the PLANTOGEAR 100 HVI and 150 HVI products negatively. The content of the residual mineral oil should, therefore, be reduced as recommended in the ISO 15380 guideline, table A1 (guidelines for changing fluid from mineral based oils to environmentally acceptable fluids) to a percentage of approximately lower than 2% mineral oil in PLANTOGEAR 100 HVI and 150 HVI. Old gears should also be flushed and rinsed before changing over to PLANTOGEAR 100 HVI and 150 HVI in order to reduce substantially the concentration of the residual mineral oil based product. The internal tank and gear coatings should be compatible with ester based products. Paints which are not compatible to esters are not recommended to be used. In general two components coating systems can be used with ester based products. The use of stainless steel tanks or stainless steel filter housings is recommended. When deep filtration filters are used, the good solvency, dissolving properties of the PLANTOGEAR 100 HVI and 150 HVI products can reduce the filter life. Clean/check or replace the oil filters in the system after 1 week after changing over to PLANTOGEAR 100 HVI and 150 HVI products. Use ester-resistant compatible sealing materials and plastic materials in general.
 
We recommend the use of viton material in dynamic stressed seals.
Observe the change-over recommendations according to ISO 15380.